. centre de ressources dilemmes et doutes le visage humain de mathématiques Qui sommes-nous Problème de mois activités de promotion babillard
Centrale des maths - centraledesmaths.uregina.ca
Dilemmes & doutes
« D & D »
. .
topic card  



liste de
. .
nouvelle recherche

7 articles trouvés pour ce sujet.
The linear thermal expansion of steel 2011-05-03
Scot pose la question :
Several questions on your site deal with the linear thermal expansion of steel. Such as how much will a piece of steel grow in length if it is heated. My question is similar but I would like to know if there is a different calculation to determine how much the diameter of a round bar will grow when heated. Can you tell me how I can calculate how the diameter of .500" round steel will increase for every degree of temperature change? If a bar is raised from 60 degrees F to 120 degrees F how much will the diameter change?
Robert Dawson lui répond.
The thermal expansion of steel 2010-12-20
roger pose la question :
Knowing that the coefficient of thermal expansion of steel is 6.5E-06 in/in/deg F. How do you calculate the loads applied as a result of the expansion?
Robert Dawson lui répond.
Thermal expansion of a steel beam 2010-06-25
chris pose la question :
If a 50 ft steel beam can expand up to 4inches when heated to 1000f How much will a 162 ft and six inches steel beam expand under the same conditions?
Robert Dawson lui répond.
Finding Density Given Volumetric Thermal Expansion Coefficient 2009-12-26
florence pose la question :
Hi- Please help me to apply the formula for this problem. The coefficient of volumetric for gold is 4.20 X 10^-5 C degrees. The density of gold is 19,300 kg/m^3 at 0.9 C degrees. What is the density of gold at 1050 degrees C. Could you please explain how to get the solution of 18,500 kg/m^3 Thank you for your help Florence
Janice Cotcher lui répond.
Coefficient thermal expansion of steel 2009-06-29
roshni pose la question :
Coefficient thermal expansion of steel is 0.00000645/in/in/deg F if F was C(celcius) then what is the answer
Robert Dawson lui répond.
Thermal Expansion of Steel 2009-06-17
Ken pose la question :
Hi there, We are rollforming steel roofsheeting in 65M lengths and the = question of linear expansion has cropped up.I would like to know what = the expansion rate of this sheet would be over a temperature rise of say = 40degree F.in mm per Meter or whatever the norm is. The sheet is 0.53mm = thick and is 700mm in width,I hope this is sufficient info to enable you = to do your calculation.Many thanks, in anticipation. Ken
Janice Cotcher lui répond.
The coefficient of thermal expansion for steel 2005-10-14
Jim pose la question :

Is the following statement true?

The coefficient of thermal expansion for steel is 0.00000645in/in/deg. Doesn't sound like much but when you run out the numbers it comes to .405504 ft/mile/deg. Still doesn't sound like much, only about 5". Then multiply by 40 degrees and you get a piece of rail that has grown by 16.22 feet in that one mile. It's not at all unusual for the rail temp to go from say, 40 deg to 80 deg on a spring or fall day. Remember that on a sunny day, the rail temp can be significantly higher than the air temp as well."

I ran the math and came up with an answer closer to 16 inches, instead of 16 feet. Which is closer to being correct?

Penny Nom lui répond.



Centrale des maths reçoit une aide financière de l’Université de Regina et de The Pacific Institute for the Mathematical Sciences.



accueil centre de ressources accueil Société mathématique du Canada l'Université de Regina PIMS