.
. centre de ressources dilemmes et doutes le visage humain de mathématiques Qui sommes-nous Problème de mois activités de promotion babillard
Centrale des maths - centraledesmaths.uregina.ca
Dilemmes & doutes
« D & D »
. .
topic card  

Sujet:

roll

liste de
sujets
. .
nouvelle recherche

33 articles trouvés pour ce sujet.
 
Page
1/1
Sens d'un mot 2000-06-01
Edward Brisse pose la question :
Serait-il possible de connaître le sens précis du mot "PORISME". Exemple : "le porisme de Poncelet".
Claude Tradif lui répond.
Roll of film 2021-11-20
Brian pose la question :
Trying to create a formula to calculate the build up on a roll of film is calculated. Except instead of of a roll, it's essentially a rectangle with two semicircles on each at the end. Example: I start with a 6" diameter core on each side, and I start winding .005" thick film on the core. The distance between the center of those cores, length of the inner rectangle is 7.125. If I continue to do this for a total length of film of 3000 feet, what will the roll length and width be. So what I need is the formula to perform this type of calculation. Can you help me? I want to be able to plug the formula in a spread sheet and to be able to input a core diameter, a film thickness and a total length and the length between the center of the two cores(which is the inner rectangle's length I'm assuming). Thanks
Harley Weston lui répond.
More on a roll of paper 2021-05-07
Stephen pose la question :
Can you help with the equations to calculate the length of paper required to achieve a target outside diameter when wrapped around a core please?

The inside diameter of the cardboard core is 76mm
The thickness of the wall of the cardboard core is 5mm
The thickness of the paper is 138microns
The desired outside diameter of the finished roll is 320mm

I hope you can help me with a solution, Thank you

Harley Weston lui répond.
The area and weight of sod 2018-12-11
Susan pose la question :
I have equipment that will cut sod 30 inches across and 75 Feet in length? how much will this be in square foot age ? Yards? Approximate weight?
Penny Nom lui répond.
The amount of material remaining on a roll 2016-11-11
Yoh pose la question :

Question from Yoh:

Hello,
I am trying to find impressions on a roll (either full roll or partial).
Let's say I have the following information.
- Outer Diameter of roll
- Inner Diameter of roll (cardboard core)
- thickness per layer
- Each cut off length (impression length)

Now let's say a roll has a 40in outer diameter, the cardboard core has a 3.75in diameter and a thickness of .002. Each impression has a cut off of 14inches.
With this the roll will have approximately 2,700 impressions. How would I find the remaining impressions if the outer diameter of the roll is only 6.5inches?

Thank you.


Penny Nom lui répond.
The length of stock on a roll 2016-09-23
Ken pose la question :
I have a roll that is 13.5 inches wide ( OD) , and is wound on a 3 inch core. the thickness of the material is 3.5 thick.
Do you know of a formula that can calculate the linear feet on that roll??

Harley Weston lui répond.
The length of a roll of paper 2015-01-12
Peggy pose la question :
roll of paper 3ft wide and roll equals 500 sq ft how long would the roll be?
Penny Nom lui répond.
Rolls of window film 2014-02-14
Travis pose la question :
This question is probably close to the same question as "roll of paper"

We have Rolls of Window Film that we are trying to figure out an equation for a spreadsheet that we can use to "inventory" our window film.

We use a caliper tool to measure the thickness of the roll in millimeters.

the core thickness = 1.90mm
Full Roll thickness(including core) = 9.08mm to 9.12mm
Film thickness = 0.06

Full Roll of Film is supposed to average 1200" of film

What equation could we use to get the approximate inches left remaining on the roll if we measured the roll including the core with the Caliper tool in Millimeters?

Harley Weston lui répond.
A steamroller with a 3 foot diameter and a 6 foot width makes 20 revolutions 2012-03-21
Robert pose la question :
A steamroller with a 3 foot diameter and a 6 foot width makes 20 revolutions. How much ground area does it pave?
Penny Nom lui répond.
A reel of paper 2011-06-03
keith pose la question :
if a full reel of paper has 7750 metres on it with a diameter of 1240mm and a core diameter of 100mm how can work out the thickness of each strip of paper therefore allowing me to work out the metreage of the roll when its half in diameter at say 620mm
Penny Nom lui répond.
How many labels are left on a roll? 2010-08-13
Melissa pose la question :
Is there a simple way to calculate how many labels are left on a roll? I thought there was a way to look at the individual label length, the label thickness and the core diameter and then measure the overall diameter to calculate how many pieces were left, but I'm struggling. I've seen a tool before- I thought we called it a circle calculator, but those parameters were all that I needed to input to spit out the correct count. I never saw what was behind the scenes for this calculation. Ie factoring in revolutions or the number of pieces on each layer, etc. Please let me know if you have any suggestions. Any assistance will be greatly appreciated!!! Thanks!
Penny Nom and Tyler Wood lui répond.
A roll of paper 2010-03-25
keith pose la question :
how many yds of paper for a roll with a width of 6.875 and a core of 3 in and a diameter of 40in?
Robert Dawson lui répond.
A paper towel roll 2009-08-19
Jeff pose la question :
I am making a spiral tube with paper that is 2" in dia. and 102" long I will be using paper that is slit 3" wide how many lineal feet of paper will I need to to cover the 102" I will be using 3 rolls of paper that will over lap the other by half to make a hard tube (paper core) in a roll of paper towels Thanks Jeff
Penny Nom lui répond.
A roll of paper 2009-07-05
mark pose la question :
is there a simple way of finding out how much is left on a roll of paper. i have read similiar questions and answers on here but all seem very complicated and not being very good at maths does not help me much. some are in inches and all have different figures to mine so if i give my figures hopefully i wil understand it better. the radius of the cardboard core is 52.25mm, the radius of the paper at 2000 linear meters is 158.625mm. the thickness is 0.17mm. when nearing the end of the paper how do i work out how much is left in a simple way. thank you in advance for any help you can give me
Harley Weston lui répond.
Winding paper after a break 2009-04-10
Olen pose la question :
Question from Olen:

I work in a paper mill and have been handed the task to search for a formula to determine how much paper needs to be added to a parent roll to make up the difference at the winder. (Ex. The spool diameter at the reel is 18.25" we measure roughly 33.5" to make two 58" rolls in the winder. If the is a paper break and the roll diameter in the winder is 30" how much do I add to a single parent roll (22" roughly) to make one 58 " and the 28" needed at the winder. I would appreciate any help to complete this task. I would like to be able to build a chart that operators can refer to based on what is needed. Thank you.

Harley Weston lui répond.
A spherical Tootsie Roll Pop 2009-04-01
Tracy pose la question :
A spherical Tootsie Roll Pop you are sucking on is giving up volume at a steady rate of .8 ml/min. How fast will the radius be decreasing when the Tootsie Roll Pop is 20 mm across?
Harley Weston lui répond.
Payroll deductions 2009-03-29
Jim pose la question :
I want to set up a spread sheet where i can enter my hourly pay or gross income, and calculate my tax deductions. I have my old pay stubs but I am stuck when I take the amount of the deduction and try to figure out the % used to calculate the amount

for example gross pay $1359, EI= $64, Fed Tax=$129, Prov tax = $35

these numbers I have provided are random but I think you can get the idea

Penny Nom lui répond.
The diameter of a roll of plastic 2009-03-24
truong pose la question :
hi. i have trouble to calculate the diameter of the plastic roll. the sheet is 765 m long and 0.8 mm to wrap around the core 400 mm in dia. please help me with the formula to calculate the dia of plastic roll, thanks in advance
Harley Weston lui répond.
A roll of film 2008-10-16
John pose la question :
I need to know how to calculate the build up on a roll of film is calculated. Example: I start with a 6" diameter core, and I start winding .005" thick film on the core, so I am adding a total of .010" to the diameter each wrap. If I continue to do this for a total length of film of 3000 feet, what will the roll diameter be? So what I need is the formula to perform this type of calculation. Can you help me? I want to be able to plug the formula in a spread sheet and to be able to input a core diameter, a film thickness and a total length and get a roll diameter.
Penny Nom lui répond.
A roll of paper 2008-03-05
Sheik pose la question :
How I Convert My Roll Weight Into Meters?
Roll Width : 241mm
Thickness : 56gsm
Weight :81 Kg

Harley Weston lui répond.
Rolling a die repeatedly (you can't just add percentages) 2007-10-04
Howard pose la question :
If my son has a 16.66% chance of rolling a particular number on a dice, and he rolls for it 6 times, he knows (from experience) that his odds of getting at least 1 right are not 100% (16.66% +16.66%+16.66% etc). He asked me if there was an equation that would give him the correct percentage chance of success when trying X times for a Y% chance of something.
Victoria West lui répond.
Rolling a metal plate 2007-07-31
k.a.suresh pose la question :
How to calculate the plate size for rolling (2010mm OD)plate thick is 6mm
Harley Weston lui répond.
Rolle's Theorem 2006-12-07
Erika pose la question :
If f(x) = (x^2)(square root of [3-x]) on the interval [0,3] is given, Does Rolle's Theorem apply? If yes, find any values of c such that f '(c)=0
Penny Nom lui répond.
Grossing up payroll wages 2006-08-27
Katie pose la question :
I really need to understand (spelled out step by step) how to gross up payroll wages.
Penny Nom lui répond.
Linear feet on a paper roll 2006-03-20
Vishal pose la question :
I WOULD WISH TO KNOW OF A STANDARD FORMULA BY WHICH I CAN CALCULATE THE LINEAR FEET OF A PAPER ROLL AS PER THE FOLLOWING DETAILS:-

THICKNESS: 150 GSM (GRAMS PER SQUARE METER)
REEL WIDTH: 85 CM
REEL DIAMETER: 140 CM
REEL INNER CORE: 10 CM
REEL WEIGHT: 946 KG's


Stephen La Rocque lui répond.
A roll of paper 2005-04-16
Tuomas pose la question :
How would you calculate a diameter of a paper reel when the paper is 0,04 millimeters thick and for example 5000 meters of it is winded on a 76 mm (3inch) core.
Penny Nom lui répond.
The length of fabric in a roll 2003-07-03
Paul pose la question :
We receive rolled fabric as part of our process and I would like to know is there a formula that could be used to estimate the overall length of the roll with out rolling the fabric out and measuring its length.
Harley Weston lui répond.
The Terror Run 2000-03-18
Danny Mclean pose la question :
A fairground's most popular attraction is a roller coaster ride known as the Terror Run. One stretch of track is called the Missile Path and is in the form of a parabolic curve. B is 180m horizontally from A and the highest point of the curve is 100m above A and B.

A.. The owner works out a quadratic expression to describe the Missile Path. What is the expression He found?

B.. A safety Engineer examined the structure and observed that points A and B were likely to be damaged due to the steepness of the Missile path near these points. The owner can see no way to make the Missile path less steep near A and B and to keep the height of the ride the same. HOW CAN IT BE DONE?


Harley Weston lui répond.
A roll of paper 2000-01-15
Richard pose la question :
I have a roll of paper, wrapped around a corrugate core, whos diameter is 10.750 in. The outer diameter of the roll is approx. 60 in. The thickness of the paper is .014 in. I am trying to find out how much linear feet of paper is left on the roll, given only the diameter of paper remaining on the core.
Chris Fisher and Harley Weston lui répond.
Trolls and Gargoyles 1999-11-02
TexGrimm pose la question :
How can you seat 6 monsters - 3 Trolls and 3 Gargoyles- at a circular table if the trolls look alike and the gargoyles look alike? Does your formula work for 9 monsters - 4 trolls and 5 gargoyles?
Penny Nom lui répond.
Rolling Circles 1999-09-12
Craig Ellis pose la question :
We have a circle of radius 3. inside the circle and tangent to the circle of radius 3 at one point is a circleof radius 1. The question is if we could roll the smaller circle around the inside of the larger circle how many revolutions would it take to get around to where we started.
Chris Fisher and Walter Whiteley lui répond.
Three dice 1998-11-17
Ryan Allinson pose la question :
Rolling three regular dice how many different ways could a sum of 10 be rolled?

Hope you can help. Can you please show me how this is done?
Penny Nom lui répond.

Rolling a seven 1998-06-11
Bruce Thompson pose la question :
What is the probablity of rolling two dice and it coming out as seven?

a) 1/6
b) 1/36

please give me the correct awnser and explain please.
Harley Weston lui répond.

 
Page
1/1

 

 


Centrale des maths reçoit une aide financière de l’Université de Regina et de The Pacific Institute for the Mathematical Sciences.

CMS
.

 

accueil centre de ressources accueil Société mathématique du Canada l'Université de Regina PIMS